Software

Software

IntelliSense® PC Software (v1.3.0)

IntelliSense® PC software v1.3.0 for Windows is used to monitor and configure the IntelliSense® Sensor Interface Module®. The IntelliSense® PC software is used to view the data being generated by the SIM. When the IntelliSense® SIM indicates a fault in the pneumatic subsystem the IntelliSense® PC software can be used to monitor current condition or export historical event logs.

  • Detailed cylinder status gives deeper insights into the health of a machine
  • Use the monitoring stream to view the unique pressure profile of your cylinder
  • Compatible with Windows 7 or later
  • IntelliSense® programming cable or a Serial RS422 to RJ45 connection is required
  • Requires Microsoft Internet Explorer (IE10 or later) or Google Chrome
  • Software version 1.3.0 requires Firmware Version R102 or later
 

IntelliSense® Patch Software

The IntelliSense® Patch 1.1 is required to allow users to update their IntelliSense® Data Gateway running software version 1.1.0 or older via a USB Drive. The IntelliSense® Patch software is run on a Windows computer that is on the same network as the IntelliSense® Data Gateway.

  • Required to update IntelliSense® Data Gateways with v1.1.0 or older software via USB.
  • Use the monitoring stream to view the unique pressure profile of your cylinder
  • Run on a Windows 7 or later PC on the same network as the Data Gateway to be patched
  • User must know the IP address of Data Gateway to be patched
  • Patch must be applied before attempting to update Data Gateway via USB drive
  • If IntelliSense® Data Gateway has Internet access this patch is not required
 

IntelliSense® Firmware (vR102)

The IntelliSense® Firmware vR102 is the brains of the IntelliSense® Platform and allows the user to select how the SIM outputs behave. They are no longer preprogrammed as end of travel. The firmware is loaded on an IntelliSense® SIM via an IntelliSense® Data Gateway or the IntelliSense® PC software. This file contains the latest updates to the IntelliSense® algorithms.

  • Enables user to select the function of the SIM outputs
  • Install using IntelliSense® PC software or an IntelliSense® Data Gateway
  • Refer to IntelliSense® user manual for installation instructions
  • Requires IntelliSense® Sensor Interface Module hardware
  • Requires IntelliSense® PC software or IntelliSense® Data Gateway
  • Firmware version R102 requires IntelliSense® PC/Data Gateway software version 1.2.0 or newer
 

IntelliSense® Data Gateway software USB update (v1.3.0)

The IntelliSense® Data Gateway software USB update v1.3.0 is used to update your IntelliSense® Data Gateway via a USB port on the gateway. Version 1.3.0 adds additional functionality to the gateway including email alerts, user configurable outputs on the SIM, and SSL encryption. The IntelliSense® Data Gateway software can be updated over the internet or by installing the IntelliSense® Data Gateway software USB update via a USB drive connected directly to the IntelliSense® Data Gateway.

  • Update IntelliSense® Data Gateway without internet access
  • Requires IntelliSense® Data Gateway hardware
  • Requires Microsoft Internet Explorer (IE10 or later) or Google Chrome
  • Software version 1.3.0 requires Firmware Version R102 or later
 

SPCS Software

System configuration and setup is easily completed using software. The SPCS-2 operates with either a 0-10 VDC or 4-20 mA analog command signal, providing closed loop pneumatic proportional control for all Bimba position feedback actuators, including the PFCN, PFCNL, PFCL, PTF and Ultran rodless cylinders with external transducers.