Products

Mid Series Venturi Vacuum Pump - VP50

The all pneumatic VP50 Series are air pilot controlled venturi vacuum pumps that feature an integral check valve and air pilot controlled blow-off for rapid part release or vacuum line clean out. Using air pilot control, VP50 Series pumps generate vacuum only when needed, minimizing compressed air consumption. 

  • All pneumatic - no electric power required
  • Precise control - individual pneumatic connections let you control the vacuum and the blow-off duration time
  • Instantaneous vacuum as needed - minimal air consumption
  • Accurate part positioning from positive vacuum and rapid blow-off
  • Easy installation - modular design speeds installation and minimizes assembly

There are three versions of the VP50 Series available (VP50-ASP shown above):

VP50 Air pilot vacuum control and blow-off

VP50-AS Adds integrated air saver circuit

VP50-ASP Adds pilot controlled blow-off and pneumatic signal output

 

To order the VP50 Series Venturi Pump or to download CAD files, click here.

 

The model number for the VP50 All Pneumatic Pilot Controlled Venturi Vacuum Pumps consists of the base model acronym (VP50) plus three alphanumeric clusters. These clusters designate the vacuum flow and vacuum level, and the final cluster indicating the version of the V50 model. Refer to the chart below for an example of model number VP50-60H-AS. This is a VP50 pump with a maximum vacuum flow of 60, maximum vacuum level of 28"Hg [948mbar], and Air Saver version of the pump. VP50 pump comes standard with a ST4 silencer, there are no further options. Note, part numbers beginning with I- denote a model with G port metric threads.

* The operating pressure of 80 PSI is standard, and the 80 designation does not appear in the part number

 

VP50

 

All-pneumatic Pilot Controlled Pump Standard Specifications

Pump Material:Anodized Aluminum, Buna-N, Brass, Acetal (for silencer material see Silencer Page)

Cartridge Material:Nylon, Buna O-Ring
O-rings available in additional materials - Consult factory for availability

Check Valve Material:Polypropylene, Buna-N, Stainless Steel

Gasket Material:NEBAR Red

Medium:Filtered (50 micron) un-lubricated, non-corrosive dry gases

Operating Temperature:-23° to ~122F [-5° to ~50°C]

Operating Pressure:80 PSI [5.5 bar]


VP50 / VP50-AS / VP50-ASP 3-Way Valve Specifications

Valve Type:Integral 3-way cartridge, pilot actuated, normally closed

Valve Body Material:Brass, Aluminum

Valve Seat Material:Buna-N

Valve Operating Pressure:0 to 100 PSI [0 to 7 bar]

Average Life:50 million cycles or better

  

Performance Level Designations:

L”0-10”Hg, [0 to 339mbar] for low vacuum/high flow applications

M”0-20”Hg, [0 to 677mbar] for medium vacuum/high flow applications

H”0-28”Hg, [0 to 948mbar] for high vacuum/standard flow applications


VP50 / VP50-AS / VP50-ASP Series Operating and Installation Requirements

Cartridge Size:C60 (M, H) and C90/C100/C150 (L, M, H) 

Supply Line:1/4” O.D. [6mm] tube 

Vacuum Line:3/8” O.D. [10mm] tube 

Pilot Line:5/32” O.D. [4mm] tube

Vacuum Line Filtration:Typically vacuum filters are not required, if desired Bimba recommends model VF250F (see In-Line Filter Page)

Mounting Screws:0.21” [5mm] diameter

 

VP80-200/250-AS / VP90-300/350-AS Operating and Installation Requirements

Pump Model:                       VP80-200-AS                      VP80-250-AS & VP90-300/350-AS

Vacuum and Supply Line: 3/8” O.D. [10mm] tube          1/2” O.D. [12mm] tube

Vacuum Line Filtration: Typically vacuum filters are not required, if desired Bimba recommends model VF375F for VP80-200/250-AS and VF500F for VP90-300/350-AS
(see In-Line Filter Page)

Mounting Screws: Mounting holes accept 10-32 [M5] screws