Mid Series Venturi Vacuum Pump - VP2X/VP2X-ADJ


Fastbreak Mid Series provides both vacuum and blow-off in one pump, using only one compressed air line -- no electricity required. The integrated pneumatic high-speed blow-off on the VP2X pump provides a fixed-duration blow-off, based on the volume of the housing. With the VP2X-ADJ adjustable vacuum pump, you can control the intensity of the blow-off using one fingertip adjustment knob.

  • Fast Response – compact, lightweight and installs close to vacuum point
  • Efficient – minimal air consumption, 
  • Reliable – operates trouble-free: straight-through design, non-clogging
  • Automatically cleans vacuum lines, no maintenance or downtime
  • Modular design – add sensors & solenoid valves for a complete vacuum system
  • Reliable part detection – factory installed miniature vacuum switches or sensors

To order the VP2X Series Venturi Pump or to download CAD files, click here.

The model number for the VP2X Series Venturi Vacuum Pumps consists of the base model acronym* (VP2X, VP2XBV or VP2XBVM8) plus six alphanumeric clusters. These clusters designate the maximum flow and vacuum levels, operating pressure, blow-off adjustment switch option, silencer, and switch or sensor options. Refer to the chart below for an example of model number VP2X-60H-ADJ-ST2-VSMP-QD-6. This is a VP2X pump with a maximum vacuum flow of 60, maximum vacuum level of 28"Hg [948mbar], operating pressure of 80 PSI, (optional) blow-off adjustment switch, ST4 silencer and a VSMP vacuum switch with 6" pigtail quick disconnect. Note, part numbers beginning with I- denote a model with G port metric threads.

Base model options:

VP2X indicates the base model
VP2XBV includes an optional integrated solenoid valve with flying leads
VP2XBVM8 includes the optional integrated valve with M8 connector





VP2X & VP2X-ADJ / VP2XBV & VP2XBV-ADJ Mid Series Pump Standard Specifications

Pump Material: Anodized Aluminum, Nebar, Brass, Buna-N, Vinyl, Nylon, Alloy Steel
(for silencer material see Silencer Page)

Cartridge Material: Nylon, Buna O-Ring
O-rings available in additional materials - Consult factory for availability

Medium: Filtered (50 micron) un-lubricated, non-corrosive dry gases

Operating Temperature:32° to ~125°F [0° to ~52°C]

Operating Pressure:80 PSI [5.5 bar] or 60 PSI [4.1 bar] – Consult Factory for other operating pressures

Cycle Rates: Up to 900/min

Blow-off Response Time: Instantaneous

Orientation: Any position

Blow-off Duration:100 milliseconds (based on system design)

Performance Level Designations:

L”0-10”Hg, [0 to 339mbar] for low vacuum/high flow applications

M”0-20”Hg, [0 to 677mbar] for medium vacuum/high flow applications

H”0-28”Hg, [0 to 948mbar] for high vacuum/standard flow applications

VP2XBV / VP2XBV Optional 2-Way Valve Specifications

Valve Type: Axial 2-Way Solenoid Valve, Normally closed

Valve Body Material: Aluminum, Buna-NBrass, Aluminum, Buna-N

Valve Operating Pressure: Vacuum to 120 PSI [-1 to 8 bar]

Electrical:24 VDC [-15% to +10% Nominal]

Power Consumption:4 watts

Response Time:6 milliseconds

Cycle Rate:80 cycles/second

Average Life:100 million cycles

Electrical Connection:Fixed leads, 24 AWG, 18” [457.2mm], optional M8 3-pin connector

LED Indicator: Yes

M8 3-pin Connection: Yes, optional


VP2X / VP2XBV /VP2XBV-ADJ / VP2X-ADJ Mid Series Operating and Installation Requirements

Cartridge Size:  C60 (M, H) and C90 (L, M, H)                        C100 (L, M, H) and C150 (L, M, H)

Supply Line:      1/4” O.D. [6mm] tube                                      3/8” O.D. [10mm] tube

Vacuum Line:    1/4” O.D. [6mm] tube                                      3/8” O.D. [10mm] tube

Vacuum Line Filtration: Typically vacuum filters are not required, if desired Vaccon recommends model VF125LPM for the VP2X/VP2XBVand model VF250LPM for the VP1X/VP2XBV-ADJ (see In-Line Filter Page)

Control Valve:3 way / 2 position (faster part release), minimum orifice – 0.125 I.D. [3 mm]

Mounting Screws: Mounting holes accept 4-40 [M3] screws