Products

Max Series Venturi Vacuum Pump - VP8X/VP8X-ADJ

The reliable Fastbreak Max Series provides both vacuum and blow-off in one pump, using only one compressed air line. No electricity required. With the VP8X-ADJ and VP8XBV-ADJ adjustable vacuum pumps, you can control the intensity of the blow-off using one fingertip adjustment knob. The VP8XBV pumps offer an integrated valve for increased production cycles.

  • Fast Response – compact, lightweight and installs close to vacuum point
  • High productivity – rapid part release, cycle rates up to 900/min
  • Efficient – minimal air consumption, 
  • Reliable – operates trouble-free: straight-through design, non-clogging
  • Automatically cleans vacuum lines, no maintenance or downtime
  • Reliable part detection – factory installed miniature vacuum switches or sensors

 

To order the VP8X Series Venturi Pump, click here.

How to Order Content

 

The model number for the VP8X Series Venturi Vacuum Pumps consists of the base model acronym* (VP8X-200, VP2XBV-200 or VP2XBVM8-200) plus four alphanumeric clusters. These clusters designate the vacuum level, operating pressure, blow-off adjustment switch option, silencer Refer to the chart below for an example of model number VP8X-200H-60-ADJ-ST6A. This is a VP8X-200 pump (maximum flow of 200) with a maximum vacuum level of 28"Hg [948mbar], operating pressure of 60 PSI, (optional) blow-off adjustment switch, and ST6A silencer. Note, part numbers beginning with I- denote a model with G port metric threads.

Base model options:

VP8X indicates the base model
VP8XBV includes an optional integrated solenoid valve with flying leads
VP8XBVM8 includes the optional integrated valve with M8 connector

 

How-to-order

 

Additional Specs Content

 

VP8X

 

VP8X & VP8X-ADJ / VP8XBV & VP8XBV-ADJ Max Series Pump Standard Specifications

Body Material: Anodized Aluminum, Nebar, Brass, Buna-N (ADJ pump only), Vinyl, Nylon, Alloy Steel
(for silencer material see Silencer Page)

Medium: Filtered (50 micron) un-lubricated, non-corrosive dry gases

Operating Temperature:32° to ~125°F [0° to ~52°C]

Operating Pressure:80 PSI [5.5 bar] or 60 PSI [4.1 bar] – Consult Factory for other operating pressures

Cycle Rates: Up to 900/min

Blow-off Response Time: Instantaneous

Orientation: Any position

Blow-off Duration:100 milliseconds (based on system design)

 
Performance Level Designations:

L”0-10”Hg, [0 to 339mbar] for low vacuum/high flow applications

M”0-20”Hg, [0 to 677mbar] for medium vacuum/high flow applications

H”0-28”Hg, [0 to 948mbar] for high vacuum/standard flow applications

 
VP8XBV / VP8XBV Optional 2-Way Valve Specifications

Valve Type: Axial 2-Way Solenoid Valve, Normally closed

Valve Body Material: Brass, Aluminum, Buna-N

Valve Operating Pressure: Vacuum to 120 PSI [-1 to 8 bar]

Electrical:24 VDC [-15% to +10% Nominal]

Power Consumption:4 watts

Response Time:6 milliseconds

Cycle Rate:80 cycles/second

Average Life:100 million cycles

Electrical Connection:Fixed leads, 24 AWG, 18” [457.2mm], optional M8 3-pin connector

LED Indicator: Yes

M8 3-pin Connection: Yes, optional

 
VP8X / VP8X-ADJ / VP8XBV / VP8XBV-ADJ Max Series Operating and Installation Requirements

Supply Line:3/8” O.D. [10mm] tube recommended

Vacuum Line:3/8” O.D. [10mm] tube recommended

Control Line:3 way / 2 position

Vacuum Line Filtration: Typically vacuum filters are not required, if desired Vaccon recommends model VF375F (see In-Line Filter Page)

Mounting: Mounting holes accept 10-32 or M5 screws